| JIS B 0201:1973 | Miniature screw threads (MOD ISO/R 1501) | 133 |
| JIS B 0202:1999 | Parallel pipe threads (MOD ISO 228-1) | 144 |
| JIS B 0203:1999 | Taper pipe threads (MOD ISO 7-1) | 151 |
| JIS B 0205-1:2001 | ISO general purpose metric screw threads-Part 1:Basic profile (IDT ISO 68-1) | 160 |
| JIS B 0205-2:2001 | ISO general purpose metric screw threads-Part 1:General plan (IDT ISO 261) | 163 |
| JIS B 0205-3:2001 | ISO general purpose metric screw threads-Part 1:Selected sizes for screws, bolts and nuts (IDT ISO 262) | 168 |
| JIS B 0205-4:2001 | ISO general purpose metric screw threads-Part 1:Basic dimensions (IDT ISO 724) | 170 |
| JIS B 0206:1973 | Unified coarse screw threads (MOD ISO 68, 263) | 176 |
| JIS B 0208:1973 | Unified fine screw threads (NEQ ISO 68, 263) | 179 |
| JIS B 0209-1:2001 | ISO general purpose metric screw threads-Tolerances-Part 1:Principles and basic data (IDT ISO 965-1 | 181 |
| JIS B 0209-2:2001 | ISO general purpose metric screw threads-Tolerances-Part 2:Limits of sizes for general purpose external and internal screw threads-Medium quality (IDT ISO 965-2) | 202 |
| JIS B 0209-3:2001 | ISO general purpose metric screw threads-Tolerances-Part 3:Deviations for constructional screw threads (IDT ISO 965-3) | 208 |
| JIS B 0209-4:2001 | ISO general purpose metric screw threads-Tolerances-Part 4:Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing (IDT ISO 965-4) | 224 |
| JIS B 0209-5:2001 | ISO general purpose metric screw threads-Tolerances-Part 5:Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing (IDT ISO 965-2) | 228 |
| JIS B 0210:1973 | Limits of sizes and tolerances for unified coarse screw threads | 234 |
| JIS B 0212:1973 | Limits of sizes and tolerances for unified fine screw threads | 242 |
| JIS B 0216:1987 | Metric trapezoidal screw threads (MOD ISO 2901, 2902, 2904) | 250 |
| JIS B 0217:1980 | Tolerance system for metric trapezoidal screw threads (MOD ISO 2903) | 259 |
| JIS B 0218:1980 | Limit of sizes and tolerances for metric trapezoidal screw threads | 276 |
| JIS B 8305:1999 | Rigid steel conduits | 300 |
| JIS B 1001:1985 | Diameter of clearance holes and counterbores for bolts and screws (MOD ISO 273) | 617 |
| JIS B 1002:1985 | Dimensions of widths across flats (MOD ISO 272, 2343, 4762) | 620 |
| JIS B 1003:1985 | Ends of parts with external metric screw thread (MOD ISO 4753) | 626 |
| JIS B 1004:1975 | Hole sizes before threading | 628 |
| JIS B 1005:1985 | Radii under the head for external threaded fasteners (MOD ISO 885) | 644 |
| JIS B 1006:1985 | Thread run-outs and thread undercuts for external threaded fasteners (MOD ISO 3508, 4755) | 646 |
| JIS B 1007:1987 | Threads and thread ends for tapping screws (MOD ISO 1478) | 651 |
| JIS B 1008:1988 | Split pin holes and wire holes for bolts, screws and studs (MOD ISO 7378) | 659 |
| JIS B 1009:1991 | Bolts, screws and studs-Nominal lengths , and thread lengths for general purpose bolts (MOD ISO 888) | 662 |
| JIS B 1012:1985 | Cross recesses for screws (MOD ISO 4757) | 666 |
| JIS B 1013:1994 | Countersunk head screws-Head configuration and gauging (IDT ISO 7721) | 683 |
| JIS B 1014:1994 | Countersunk flat head screws-Part 2:Penetration depth of cross recesses(IDT ISO 7721-2) | 686 |
| JIS B 1015:2001 | Hexalobular internal driving feature for bolts and screws(IDT ISO 10664) | 690 |
| JIS B 1021:1985 | Tolerance system for threaded fasteners (MOD ISO 4759-1, -2) | 697 |
| JIS B 1022:1999 | Tolerances for fasteners-Part 3:Plain washers for bolts, screws and nuts-Product grades A and C (IDT ISO 4759-3) | 719 |
| JIS B 1041:1993 | Fasteners-Surface discontinuities-Part 1:Bolts, screws and studs for general requirements (IDT ISO 6157-1) | 729 |
| JIS B 1042:1998 | Fasteners-Surface discontinuities-Part 2:Nuts (IDT ISO 6157-2) | 739 |
| JIS B 1043:1993 | Fasteners-Surface discontinuities-Part 3:Bolts,screws and studs for special requirements(IDT ISO 6157-3) | 750 |
| JIS B 1044:2001 | Fasteners-Electroplated coatings (IDT ISO 4042) | 765 |
| JIS B 1045:2001 | Fasteners-Preloading test for the detection of hydrogen embrittlement-Parallel bearing surface method (IDT ISO 965-5) | 787 |
| JIS B 1051:2000 | Mechanical properties of fasteners made of carbon steel and alloy steel-Part 1:Bolts, screws and studs (IDT ISO 898-1) | 796 |
| JIS B 1052:1998 | Mechanical properties of steel nuts (MOD ISO 898-2, -6) | 821 |
| JIS B 1053:1999 | Mechanical properties of fasteners made of carbon steel and alloy steel-Part 5:Set screws and similar threaded fasteners not under tensile stresses (IDT ISO 898-5) | 860 |
| JIS B 1054-1:2001 | Mechanical properties of corrosion-resistant stainless-steel fasteners-Part 1:Bolts, screws and studs | 868 |
| JIS B 1054-2:2001 | Mechanical properties of corrosion-resistant stainless-steel fasteners-Part 2:Nuts (IDT ISO 3506-2) | 889 |
| JIS B 1054-3:2001 | Mechanical properties of corrosion-resistant stainless-steel fasteners-Part 3:Set screws and similar fasteners not under tensile stress (IDT ISO 3506-3) | 904 |
| JIS B 1055:1995 | Tapping screws-Mechanical properties (IDT ISO 2702) | 917 |
| JIS B 1056:2000 | Prevailing torque type steel hexagon nuts-Mechanical and performance properties (IDT ISO 2320) | 930 |
| JIS B 1057:2001 | Mechanical properties of non-ferrous metal fasteners (MOD ISO 8839) | 951 |
| JIS B 1058:1995 | Mechanical properties of fasteners Part 7:Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm (IDT ISO 898-7) | 966 |
| JIS B 1059:2001 | Drilling screws with tapping screw thread-Mechanical and functional properties (IDT ISO 10666) | 970 |
| JIS B 1071:1985 | Method of verification for size and geometry of threaded fasteners | 977 |
| JIS B 1081:1997 | Threaded fasteners-Axial load fatigue testing-Test methods and evaluation of results (IDT ISO 3800) | 1031 |
| JIS B 1082:1987 | Stress area and bearing area for threaded fasteners | 1052 |
| JIS B 1083:1990 | General rules for tightening of threaded fasteners | 1060 |
| JIS B 1084:1990 | Method of tightening test of threaded fasteners | 1080 |
| JIS B 1085:1995 | Cone proof load test on nuts (IDT ISO 10485) | 1091 |
| JIS B 1086:1998 | Widening test on nuts (IDT ISO 10484) | 1093 |
| JIS B 1091:1991 | Fasteners-Acceptance inspection (IDT ISO 3269) | 1096 |
| JIS B 1101:1996 | Slotted head screws (NEQ ISO 1207, 1580, 2009, 2010) | 1109 |
| JIS B 1111:1996 | Cross recessed head screws (NEQ ISO 7045, 7046-1, -2, 7047) | 1145 |
| JIS B 1116:1980 | Slotted head machine screws for precision instruments | 1172 |
| JIS B 1119:1995 | Machine screws and nuts for spectacle frames (MOD ISO 11381) | 1184 |
| JIS B 1188:1995 | Cross recessed head screws with captive washer | 1192 |
| JIS B 1117:1995 | Slotted set screws (NEQ ISO 4766, 7434～7436) | 1216 |
| JIS B 1118:1995 | Square head set screws | 1233 |
| JIS B 1177:1997 | Hexagon socket set screws (MOD ISO 4026～4029) | 1242 |
| JIS B 1115:1996 | Slotted head tapping screws (NEQ ISO 1481～1483) | 1256 |
| JIS B 1122:1996 | Cross recessed head tapping screws (NEQ ISO 7049～7051) | 1270 |
| JIS B 1123:1996 | Hexagon head tapping screws (NEQ ISO 1479) | 1289 |
| JIS B 1125:1995 | Self drilling tapping screws | 1300 |
| JIS B 1126:1995 | Hexagon washer head tapping screws (IDT ISO 7053) | 1321 |
| JIS B 1127:1995 | Hexagon flange head tapping screws (IDT ISO 10509) | 1325 |
| JIS B 1163:2001 | Square nuts | 1578 |
| JIS B 1167:2001 | T-Slot nuts | 1585 |
| JIS B 1169:1994 | Eyenuts | 1590 |
| JIS B 1170:2001 | Hexagon slotted and castle nuts | 1599 |
| JIS B 1181:1993 | Hexagon nuts and hexagon thin nuts (MOD ISO 4032～4036, 8673～8675) | 1610 |
| JIS B 1183:2001 | Domed cap nuts | 1649 |
| JIS B 1185:1994 | Wing nuts | 1656 |
| JIS B 1190:1999 | Hexagon nuts with flange (MOD ISO 4161) | 1668 |
| JIS B 1196:2001 | Weld nuts | 1677 |
| JIS B 1199-1:2001 | Prevailing torque type nuts-Part 1:Hexagon nuts with non-metallic insert (MOD ISO 7040, 7041, 10511, 10512) | 1691 |
| JIS B 1199-2:2001 | Prevailing torque type nuts-Part 2:All-metal hexagon nuts (MOD ISO 7042, 7719, 7720, 10513) | 1707 |
| JIS B 1199-3:2001 | Prevailing torque type nuts-Part 3:Hexagon nuts with flange with non-metallic insert (MOD ISO 7043, 12125) | 1721 |
| JIS B 1199-4:2001 | Prevailing torque type nuts-Part 4:All-metal hexagon nuts with flange (MOD ISO 7044, 12126) | 1734 |
黄页
黄页
黄页
黄页
非标黄页
咨询系统
RSS
